
C1000X Gen 2
- you buy new from Anker US today
- you run loads up to 2,000W
- you have 600W of solar

C800
- you already own one
- 1,200W covers your loads
- you use its storage compartment
Prices and stock checked by our price engine on November 21, 2026 at 7:00 PM EST. Each product is rechecked several times a day; the time refreshes when you load the page.
Own a C800? Keep it. Shopping today? Anker’s US page for it now opens a different station.
The Anker SOLIX C800 stored 768Wh of LFP and delivered 1,200W from five AC outlets, with 1,600W SurgePad for heaters, 300W of solar, a 58-minute UltraFast refill, a 20ms UPS and a storage compartment under the lid, at 23.15 lb; Anker US no longer sells it, and its page redirects to the C1000 Gen 2. The Anker SOLIX C1000X Gen 2 stores 1,024Wh and delivers 2,000W, switches in 10ms, takes 600W of solar and refills in 49 minutes, rated for 4,000 cycles against 3,000. What the X doesn’t give you is a full spec sheet: Anker’s US page lists no weight, size or outlet count.
Below: what separates them with numbers, a 20-second calculator for your own gear, seven modeled situations, the documented replacement, and what we could and could not verify.
The C1000X Gen 2 is the bigger, faster unit: a third more battery, 800W more output, twice the solar input, a 10ms UPS against 20ms and 1,000 more rated cycles. The C800 is no longer sold by Anker US; if you own one, nothing here forces an upgrade.
- you run up to 2,000W
- you use up to 600W of solar
- you want a 10ms UPS
- you own one that works
- 1,200W is enough
- you use its cable drawer
The five differences that decide it
Both use LFP cells and the Anker app, both have a UPS, and neither takes an extra battery. These five gaps decide it.
Will it run your setup? Check in 20 seconds
Estimates use 85% usable capacity and 70% of rated solar output. Real results vary with temperature, inverter load, shade and appliance cycling. Fridge and freezer watts are daily averages and do not include compressor startup surges.
Runtime by appliance, one at a time
Simple energy estimates, not measured runtimes. About 870Wh usable on the C1000X Gen 2 and 653Wh on the C800; no independent test has measured either.
Appliance for appliance, the C1000X Gen 2 lasts 33% longer than the C800.
Same appliance, same watts: the gap is always the size of the battery.Get our Black Friday alerts for Anker SOLIX
We track live prices on 40+ models from Jackery, EcoFlow, BLUETTI and Anker SOLIX. When a deal beats the lowest price we've recorded, you'll hear from us. During Black Friday week, one short recap a day at most.
Unsubscribe in one click. We may earn a commission when you buy through our links, at no extra cost to you. Privacy Policy
What the current options cost today
Anker’s C800 page now redirects to the C1000 Gen 2, which shares the C1000X Gen 2’s 1,024Wh, 2,000W and 10ms figures. If a seller still has a C800, check that it is new and that Anker’s 5-year warranty applies. Both prices move often.
The third option: the Anker SOLIX C1000 Gen 2 at $469.99
Anker SOLIX C1000 Gen 2: $469.99 today
The model Anker’s C800 page now redirects to, and the documented version of the X: 1,024Wh and 2,000W from five AC outlets, a 10ms UPS, 600W of solar and a 49-minute refill, rated for 4,000 cycles, at 24.9 lb, with five published independent tests. Like the C800, it has no battery port. Pick it if you want the full spec sheet. Our C1000 Gen 2 review goes deeper. See the C1000 Gen 2 at Anker.
Seven modeled situations, worked out
Same formula as the calculator above: 85% of the rated capacity, no extra battery.
24-hour outage, essentials only
An evening and most of a night on either; the C1000X Gen 2 lasts about two hours longer. Neither takes an extra battery for a full day.
Space heater on high
The C1000X Gen 2 runs it at full power. The C800’s 1,200W inverter can only drive it on SurgePad, which runs heating loads at reduced power.
Home office through an outage
A workday on either. The C1000X Gen 2 switches in 10ms, under the roughly 16ms a desktop PC power supply rides through; Anker rates the C800 at 20ms, enough for a router but marginal for some PCs.
CPAP, a weekend away
Two nights on the C800, closer to three on the C1000X Gen 2, before you need the sun or the car.
Refill from the wall before a storm
Anker’s figures. The C1000X Gen 2’s 49 minutes needs UltraFlash switched on in the app; the C800 charges at 750W by default, about 90 minutes.
Refill from solar, each at its maximum
With twice the input, the C1000X Gen 2 refills a bigger battery faster. Anker quotes 1.8 hours for it and 80% in 2.3 hours for the C800 in ideal sun.
Carrying it
Anker’s US spec table gives 23.15 lb for the C800. Anker publishes no weight for the C1000X Gen 2, only that it is 11% lighter than comparable units; the C1000 Gen 2 with the same battery weighs 24.9 lb.
Eight more differences, the spec sheet and the box
Smaller gaps that rarely decide the purchase, then the full specifications and what ships in the box.
C1000X Gen 2 and C800 weight, dimensions and full specifications
Weight: 23.15 lb for the Anker SOLIX C800, per Anker’s US spec table; Anker publishes no weight for the C1000X Gen 2. Dimensions: 14.61 × 8.07 × 9.96 in for the C800; none published for the C1000X Gen 2. Everything else is in the sheet below.
Anker SOLIX C1000X Gen 2 and Anker SOLIX C800 full specifications
Every published figure for both units, grouped. Green marks the better value.
What’s in the box
C1000X Gen 2
- C1000X Gen 2 power station1,024Wh
- AC charging cable
- Car charging cable
- Quick start guide, safety and warranty card
C800
- C800 power station768Wh, 23.15 lb
- AC charging cable
- Car charging cable
- User manual
- Built-in storage compartmentunder the lid
C1000X Gen 2 contents from Anker US; C800 contents from its archived US page and manual.
07 · ChargingHow fast each one refills
Shorter bar, faster refill. Each row is scaled to its slower unit.
C1000X Gen 2: recharges from AC, solar, a car outlet, a generator or an alternator, per AnkerC800: 750W by default and 1,100W in UltraFast, with a car cable in the box, per Anker’s archived US page
Our solar times assume panels deliver 70% of their rating; the brands’ figures assume ideal sun.
Every port, side by side
C1000X Gen 2
C800
Practical consequence: the C800’s five AC outlets, two USB-C, two USB-A and 12V socket are all documented. Anker itemizes none of the C1000X Gen 2’s 9 ports; its product photo shows four AC outlets. Count your plugs before you choose.
09 · NoiseNoise: C1000X Gen 2 vs C800
Anker gives the Anker SOLIX C1000X Gen 2 0 to 20dB under 200W and published no rating for the Anker SOLIX C800. No published test has measured either.
Anker’s figure only; no independent measurement found.Every figure we found, with its source
No decibel figure published.
Measured by a tester Brand figure
- Charge during the day, or lower the charging speed in the Anker app overnight.
Cold and heat: C1000X Gen 2 vs C800
The Anker SOLIX C800 charges from 32°F to 104°F and runs from −4°F to 104°F, per Anker. Anker publishes no range for the Anker SOLIX C1000X Gen 2.
Figures from Anker’s archived C800 page; none published for the C1000X Gen 2.- Charge either one indoors in winter: the C800 doesn’t charge below 32°F, and Anker publishes no range for the C1000X Gen 2.
App, UPS and smart features
The Anker SOLIX C1000X Gen 2 switches faster (10ms against 20ms) and refills faster. The Anker SOLIX C800 documents more of its app: Wi-Fi, Bluetooth, timers and firmware updates.
Neither takes an extra battery.Green zone: a switch under about 16ms, which most desktop PCs ride through without restarting.
Can it run a heater above its rating? The Anker SOLIX C800 runs heating loads up to 1,600W on SurgePad at reduced power; the Anker SOLIX C1000X Gen 2 page lists 2,400W of surge but no SurgePad mode, and its 2,000W rating already covers most heaters.
Can you add a battery later? The Anker SOLIX C800 has no battery port; the Anker SOLIX C1000X Gen 2 page lists none.
How does the app connect? The Anker SOLIX C800 connects over Wi-Fi or Bluetooth; the Anker SOLIX C1000X Gen 2 page mentions remote monitoring in the Anker app without naming the connection.
Does it work as a UPS? The Anker SOLIX C1000X Gen 2 switches in 10ms and the Anker SOLIX C800 in 20ms, per Anker.
Does it have a fast charging mode? The Anker SOLIX C1000X Gen 2 needs UltraFlash switched on in the app for 49 minutes; the Anker SOLIX C800 charges at 750W by default and at 1,100W in UltraFast.
Warranty and support
Both carry 5 years: the Anker SOLIX C800 per Anker’s US spec table, the Anker SOLIX C1000X Gen 2 once registered, per Anker’s US registration page. An existing C800 keeps the term it was sold with.
Same term. The C1000X Gen 2 is rated for 1,000 more cycles.Subject to each brand’s warranty terms and eligibility.
Anker rates the C1000X Gen 2 at 4,000 cycles to 80% and the C800 at 3,000+ to 80%, about 11 and 8 years at one full cycle a day. Calendar aging and heat also reduce capacity, so read the ratings as a ceiling.
- Register a new C1000X Gen 2 with Anker when it arrives: Anker’s registration page says that activates the 5-year coverage.
- Buying a C800 from a remaining seller, check that it is new and that Anker’s warranty applies.
What reviewers report
We have not lab-tested these two units, and we found no published hands-on review of the C800 on its own or of the C1000X Gen 2. Reviews of their sibling models are not carried over.
C1000X Gen 2: no verifiable independent test foundC800: no verifiable independent test found
Practical limits before you buy
- Anker US no longer sells the C800. Its page redirects to the C1000 Gen 2.
- The C1000X Gen 2 page gives no weight, size, temperature range or port list. Check the unit before you plan around them.
- The C800 stops at 1,200W. SurgePad runs heaters above that at reduced power; motors need the continuous rating.
- The C800 charges at 750W by default. The 58-minute refill needs UltraFast.
- Neither takes an extra battery.
- The C800 doesn’t charge below 32°F. Anker publishes no range for the X, so charge it above freezing too.
- C1000X Gen 2, per its US documentation: The 0-20dB quiet claim applies only under 200W load.
- C1000X Gen 2, per its US documentation: Fast AC recharging uses a 1,500W AC input and must be activated in the app to reach 49 minutes.
- C1000X Gen 2, per its US documentation: Solar input up to 600W; full solar recharge about 1.8 hours in optimal sun.
- C1000X Gen 2, per its US documentation: 2,000W output across 9 ports, 2,400W surge support; battery keeps over 80% after 4,000 cycles.
- C800, per Anker’s archived US page and manual: SurgePad does not work in bypass mode and suits heating devices, not precision instruments.
- C800, per Anker’s archived US page and manual: The USB-C ports are output only.
Frequently asked questions
What is the difference between the Anker C1000X Gen 2 and the C800?
The C1000X Gen 2 has 1,024Wh, 2,000W, a 10ms UPS, 600W of solar and a 49-minute refill, rated for 4,000 cycles. The C800 had 768Wh, 1,200W from five outlets, a 20ms UPS, 300W of solar, a 58-minute refill and a storage compartment, rated for 3,000+ cycles, at 23.15 lb.
Is the C800 discontinued?
Anker US no longer sells it: its page redirects to the C1000 Gen 2, and Anker’s refurbished C800 listing showed sold out on October 31, 2026.
What replaced the C800?
Anker US points the C800 page to the C1000 Gen 2: 1,024Wh, 2,000W and a 10ms UPS, with a published weight of 24.9 lb.
Can the C800 run a space heater?
Its 1,200W inverter runs heaters above that only on SurgePad, at reduced power. The C1000X Gen 2 runs a 1,500W heater at full power for about 35 minutes.
Which is better as a UPS?
The C1000X Gen 2: 10ms against 20ms for the C800, per Anker. A desktop PC power supply typically rides through about 16ms.
How long will each run a refrigerator?
At a 60W average, about 14.5 hours on the C1000X Gen 2 and 10.9 hours on the C800.
How much do they weigh?
23.15 lb for the C800, per Anker’s US spec table. Anker publishes no weight for the C1000X Gen 2.
What warranty do they have?
5 years for the C800 per its US spec table; 5 years once registered for the C1000X Gen 2, per Anker’s US registration page.
Related comparisons and reviews
How we compared and sources
Research-based comparison. We have not physically tested these units. C1000X Gen 2 specs come from its Anker US page, which has no full spec table. C800 specs come from Anker’s US page as archived on May 19, 2026 and its US user manual (A1753), because Anker US no longer lists it. Checked on October 31, 2026.
- Specs: Anker US, C1000X Gen 2 (A1765111), read on October 31, 2026; Anker US, C800 (archived May 19, 2026) and its US user manual (A1753); ankersolix.com/products/c800 now returns a permanent redirect to the C1000 Gen 2.
- The C1000X Gen 2 page has no spec table: no weight, size, temperature range or port list; its four AC outlets are counted on Anker’s product photo. Warranty from Anker’s US registration page.
- Runtime = capacity × 0.85 ÷ watts. Solar harvest = min(panel watts, max input) × sun hours × 0.70. Cost per lifetime kWh = price ÷ (cycles × capacity in kWh).
1,024Wh and 2,000W against 768Wh and 1,200W. The C800 is no longer sold by Anker US.
Prices checked November 21, 2026 at 7:00 PM EST
Looking at other models? Browse all power station comparisons, or pick any two models on the hub and we point you to the right duel.
Originally published: November 14, 2026